Federal 2-Jet Air Plugs

$378.00 -- Mahr-Federal

Purchase Federal 2-Jet Air Plugs

Through Hole, Blind Hole and Counterbore*
  Size Ranges
(Inch/Metric)
   Above Thru & Including
LOW Magnification

 For 1260:1, 2500:1, 4000:1, 5000:1 & 8000:1
  .123"/3.1mm+  .185"/4.7mm
 .185"/4.7mm  .248"/6.3mm
 .248"/6.3mm  .3735"/9.4mm
 .3735"/9.4mm  .540"/13.7mm
 .540"/13.7mm  .825"/21.0mm
 .825"/21.0mm  1.135"/28.8mm
 1.135"/28.8mm  1.484"/37.7mm
 1.484"/37.7mm  2.010"/51.1mm
 2.010"/51.1mm  2.510"/63.8mm
 2.510"/63.8mm  3.004"/76.3mm
 3.004"/76.3mm  3.510"/89.2mm
 3.510"/89.2mm  4.010"/101.9mm
 4.010"/101.9mm 4.500"/114.3mm 
HIGH Magnification

For 1000"1, 16000:1, 20000:1 & 32000:1 		 .062"/1.6mm   .093"/2.4mm
 .093"/2.4mm  .123"/3.1mm
 .123"/3.1mm++  .185"/4.7mm
 .185"/4.7mm  .248"/6.3mm
 .248"/6.3mm  .365"/9.3mm
 .365"/9.3mm  .540"/13.7mm
 .540"/13.7mm  .825"/21.0mm
 .825"/21.0mm  1.135"/28.8mm
 1.135"/28.8mm  1.484"/37.7mm
 1.484"/37.7mm  2.010"/51.1mm
 2.010"/51.1mm  3.004"/76.3mm
* Two-Jet, Open Jet Style only; One-Jet, Three-Jet, Four-Jet and Six-Jet Air Plugs and Air Plugs for special applications also available - contact service@measurenow.com
+ For 2500:1 thru 8000:1 - Blind Hole Air Plug sizes start at .155"/3.9mm
++ For 10000:1 thru 32000:1 - Blind Air Plug sizes start at /125"/3.2mm

Features:

  • Tooling is interchangeable without adjusting system magnification
  • Federal Air Plugs have large clearance allowing easy entrance into the hole being measured and greater measuring range
  • Long life - wide clearance and hard chrome (optional) body extends useful life of the Air Plug
  • Deep, recessed jets - Air jets are recessed into the plug body which protects them from damage
  • Large jet size eliminates clogging from dirts and oils
PLUG IDENTIFICATION

Air Plugs are marked with an identification number which identifies its size, number of jets, plug style, and the Dimensionair Model the plug should be used with.

For example, DP50-T2-1.000 is the identification number of an Air Plug for a 2095184 or a standard magnification 832 Dimensionair (DP50), through-hole style with two jets (-T2), and 25../1.000in nominal size (-1.000).

The number (50) which identifies the Dimensionair intended is marked on the plug and also appears on the dial of the Dimensionair to help in matching the tooling to its corresponding Dimensionair Model.

THROUGH HOLE PLUGS (DP50 - DP20 & 60)
3-4.7mm/.123-.185"
 
Minimum recommended hole length: 4.8mm/.187in		 14.1-37.8mm/.588-1.484"
 
Minimum recommended hole length:
6.35mm/ .250in
With guide sleeve or stop collar:
1.77mm/ .070in
May be used with AHA-4 or -5
Extensions for deep holes.
4.7-6.3mm/.185-.248"
 
Minimum recommended hole length:
4.8mm/ .187in
 37.8-76.5mm/1.484-3.004"
 
Minimum recommended hole length:
6.35mm/ .250in
With guide sleeve or stop collar:
1.77mm/ .070in
May be used with AHA-4 or -5
Extensions for deep holes.
6.3-9.5mm/.248-.3735"
 
Minimum recommended hole length: 6.35mm/ .250in
With guide sleeve or stop collar:
1.8mm/ .070in
9.5-14.1mm/.3735-.588"
 
Minimum recommended hole length:
6.35mm/ .250in
With guide sleeve or stop collar:
1.77mm/ .070in
May be used with
AEX-1 or -2 Extensions
for deep holes.
 76.5-114.3mm/3.004-4.50"
 
Minimum recommended hole length:
6.35m /.250in
With guide sleeve or stop collar:
1.8mm/.070in



BLIND HOLE/COUNTERBORE PLUG (DP50 - DP20 & 60)
3.9-4.7mm/.155-.185"
 
Minimum recommended hole length:
6.35mm/ .250in.
Note: Masters must simulate workpiece for
holes of this size.
 11.8-14.1mm/.467-.556"
 
Minimum recommended hole length:
6.35mm/ .250in.
Shorter bores can be checked. Consult
Mahr Federal Customer Resource Center.
May be used with Extensions AEX-1 or -2
for deep holes.
 4.7-6.3mm/.185-.248"
Minimum recommended hole length:
6.35mm/.250in.
 14.1-37.8mm/.588-1.484"
 
Minimum recommended hole length: 6.35mm/
.250in. Shorter bores can be checked. Consult
Mahr Federal Customer Resource Center. May be
used with AHA-4 or -5 Extensions for deep holes.
6.3-9.47mm/.248-.373"
 
Minimum recommended hole length:
6.35mm/.250in
Shorter bores can be checked.
 37.8-76.5mm/1.484-3.004"

Minimum recommended hole length: 6.35mm/
.250in. Shorter bores can be checked. Consult
Mahr Federal Customer Resource Center. May
be used with AHA-4 or -5 Extensions
for deep holes.
9.47-11.8mm/.373-.467"
 
Minimum recommended hole length:
.250in. Shorter bores can be checked.
May be used with extension AHA-28 for
deep holes.
  769.5-108.2mm/3.004-4.50"

Minimum recommended hole length:
6.35mm/ .250in.


THROUGH HOLE PLUG (DP10 - DP5)
 1.6-6.4mm/.062-.250"

Minimum recommended hole
length: 3.18mm/ .125in.
 11.1-44.5mm/.437-1.750"

Minimum recommended hole length:
3.18mm/ .125in with proper support
min. is 1.14mm/ .045in. May be used
with AHA-23 or -24 Extensions for
deep holes.
 6.4-9.5mm/.250-.3735"

Minimum recommended hole length:
3.18mm/ .125in.
With guide sleeve or stop collar:
1.14mm/ .045in.
 44.5mm & Up/ 1.750" & Up

Minimum recommended hole length: 3.18mm/
.125in. With guide sleeve or stop collar:
1.14mm/ .045in. May be used with AHA-23
or -24 Extensions for deep holes.
 9.5-11.1mm/.3735-.437"

Minimum recommended hole length: 3.8mm/
.125in. With guide sleeve or stop collar:
1.14mm/ .045in. May be used with AHA-
23 or -24 Extensions for deep holes.



BLIND HOLE PLUGS (DP10-DP5)
 3.2-6.4mm/.125-.250"

Minimum recommended hole length:
3.96mm/ .156in.
  6.4-11.1mm/.250-.437"

Minimum recommended hole length:
3.18mm/ .125in.
 11.1mm & Up/.437" & Up

 Minimum recommended hole
length: 3.18mm/ .125”.
Use AHA-23 or -24 Extensions
for deep hole applications.



THROUGH HOLE PLUG (DP100)
 9.525-12.7mm/.375-.500"

Minimum recommended hole length:
6.35mm/ .250in, with proper support
min. is 3.18mm/ .125in. May be used
with AEX-1 or -2 Extensions for deep
holes.
 37.8-76.5mm/1.490-3.004"

 Minimum recommended hole
length: 6.35mm/ .250in.
May be used with AHA-4 or -5
Extensions for deep holes.
12.7-37.8mm/.500-1.490"

 Minimum recommended hole length:
6.35mm/ .250in, with proper support min.
is 1.14mm/ .125in. May be used with
AHA-4 or -5 Extensions for deep holes.		 76.5mm & Up/3.004" & Up

Minimum recommended hole
length: 6.35mm/ .250in.


BLIND HOLE/COUNTERBORE PLUGS
 9.525-14.25mm/.375-.561"

Minimum recommended
hole length: 7.9mm/ .312in.
  37.8-76.3mm/1.490-3.004"

Minimum recommended hole
length: 7.9mm/ .312in. Use
with AHA-4 or -5 handles
for deep hole applications.
14.25-37.8mm/.561-1.490"

 Minimum recommended
hole length: 7.9mm/ .312in.
Use with AHA-4 or -5
handles for deep hole applications.		  76.3-114.3mm/3.004-4.500"


Purchase Federal 2-Jet Air Plugs

  • Magnification: Low; High
  • Range: .093-.123" (2.4-3.1mm); .123-.185" (3.1-4.7mm); .185-.248" (4.7-6.3mm); .248-.3735" (6.3-9.4mm); .3735-.540" (9.4-13.7mm); .540-.825" (13.7-21.0mm); .825-1.135" (21.0-28.8mm); 1.135-1.484" (28.8-37.7mm); 1.484-2.010" (37.7-51.1mm); 2.010-2.510" (51.1-63.8mm); 2.510-3.004" (63.8-76.3mm); 3.004-3.510" (76.3-89.2mm); 3.510-4.010" (89.2-101.9mm); 4.010-4.500" (101.9-114.3mm)
  • Quantity: 1; 2 & Up
  • Material: High Chrome Content; Chrome
  • Style: Through Hole; Blind Hole; Counterbore

    Other products in the category Air Gaging:

  • Federal Dimensionair Air Rings -- Mahr-Federal

  • Edmunds Air Plugs -- Edmunds

  • Edmunds Air Rings -- Edmunds

  • Federal Dimensionair Air Gages (single master system) -- Mahr-Federal

  • Federal 832 Dimensionair Digital Electronic Amplifier -- Mahr-Federal

  • Federal Micro Dimensionair -- Mahr-Federal



    StoreFront | Air Gaging | Amplifiers | Bore Gages | Borescopes | Chamfer Gage | CMM & Accessories | Coating Thickness Gage | Countersink Gage | Depth Gages | Dial Calipers | Dial Indicators | Digital Calipers | Digital Indicators | Durometers | Environment Testing | Force Gages | Gage Blocks | Granite Plates & Accessories | Groove Gages | Hardness Testers | Height Gages | ID/OD Gages | Indicator Stands | Laser Micrometer | Length Measurement | Material Thickness Gages | Measuring Wheels | Metrology Casting Material | Micrometers | Microscopes | NDT | Optical Comparators | Pin-Plug Gage Sets | Precision Measuring Tapes | Protractors | Ring Gages | Snap Gages | SPC | Surface Finish Gages | Surveillance Masters | Test Indicators | Thickness Gages | Thread Gages | Transducers | Ultrasonic Gages | Video Measurement System | Vision Fixturing Systems | Wireless Data Collection





    MeasureNOW
    MeasureNOW shopping cart powered by Nexternal

    		•